This article contains affiliate links: if you buy through them we may earn a commission, at no extra cost to you. Read our affiliate disclosure.
It is the first week of an after-school archery club. One parent has ordered a dozen long carbon arrows because the pack said “fits most bows”. The coach picks one up, holds it against a young archer’s draw, and shakes her head: too long, and almost certainly the wrong stiffness for a light bow.
The short answer: three numbers decide the arrow. Length comes from how far you draw, spine (how stiff the shaft is) comes from your bow’s draw weight at that length, and material (aluminum, carbon or fiberglass) comes from your age, budget of effort and where you shoot. Easton, the maker whose charts and tuning guide we read for this page, builds its selection around exactly those inputs. This guide explains each one in plain words, then compares seven arrow listings by what they state, with no prices because they change.
Our top picks

Easton Genesis XX75 aluminum (6 pack)
- 7075 aluminum, hard-anodized (per listing)
- Straightness +/-.005 in, weight +/-2.5% (per listing)
- Factory assembled: UNI bushing, nock, point, vanes
- Listing: approved arrow for NASP tournaments and events
$43.97 at Amazon, as of Nov 22, 2026 12:07 UTC
Check price on Amazon
SHARROW 30 in aluminum, spine 500 (12 pack)
- Aluminum, 30 inch
- Spine 500 (listing)
- OD 7.6 mm, ID 6.5 mm
- Screw-on tips; nocks not glued

GPP 30 in fiberglass target arrows (12 pack)
- 30 inch fiberglass shaft
- 6 mm OD, about 28.5 g (1 oz)
- Listing: bows up to 40 lb
- 2.5 inch shield vanes
$19.99 at Amazon, as of Nov 22, 2026 12:07 UTC
Check price on Amazon
Bear Archery Youth fiberglass, 24 in (3 pack)
- 24 inch fiberglass shaft
- Nock, point and vanes pre-installed
- Three arrows per card
- Listing: available in four sizes
$31.03 at Amazon, as of Nov 22, 2026 12:07 UTC
Check price on Amazon
Hunter Ian pure carbon, spine 600 (6 pack)
- Carbon, 30 inch shaft (31.5 inch overall)
- Spine 600
- ID 6.2 mm, OD 7.1 mm, 5.54 GPI
- For bows 30 to 35 lb (listing)
$37.99 at Amazon, as of Nov 22, 2026 12:07 UTC
Check price on Amazon
Pinals carbon, spine 400, 12 pack with spare inserts
- Pure carbon, ID 0.244 in (6.2 mm)
- Spine 400, 4 inch turkey feather
- Listing: 25 to 70 lb draw weight
- Extra aluminum inserts for cut shafts

Linkboy pure carbon, many spine choices (12 pack)
- Pure carbon, ID 6.2 mm
- Straightness +/-.003 in (listing)
- Spines offered: 300 to 1000
- Removable stainless steel tips
The picks compared
| Product | Material | Length (from listing) | Spine / bow weight (from listing) | What the listing says |
|---|---|---|---|---|
| Easton Genesis XX75 | Aluminum (7075) | Not stated | Not stated | NASP approval wording, assembled, +/-.005 in straightness |
| SHARROW aluminum | Aluminum | 30 inch | Spine 500; draw weight not stated | OD 7.6 mm, glue-free nocks, 12 pack |
| GPP fiberglass | Fiberglass | 30 inch | No spine; bows up to 40 lb | 6 mm OD, 28.5 g, youth over 12 |
| Bear Archery youth | Fiberglass | 24 inch | No spine; weight range not stated | Pre-fletched, 3 per card, four sizes |
| Hunter Ian carbon | Carbon | 30 inch shaft, 31.5 inch overall | Spine 600; 30 to 35 lb | 5.54 GPI, +/-0.006 in straightness |
| Pinals carbon | Carbon | 30 or 32 inch (title) | Spine 400; 25 to 70 lb | 12 spare inserts, turkey feather |
| Linkboy carbon | Carbon | Not stated | Spines 300 to 1000 offered | +/-.003 in straightness, stainless tips |
The picks in detail
1. Easton Genesis XX75 aluminum (6 pack): aluminum arrow for school and nasp-style programs
The listing presents this as a ready-to-shoot aluminum arrow from the maker whose charts we read, with stated straightness and weight tolerances. It is the pick for school and club programs that ask for a specific approved arrow.
What the Amazon listing says
- Listing title: Easton Genesis XX75 aluminum arrows with diamond vanes, 6 pack, silver
- States it is the official NASP approved arrow, the only one approved for all NASP tournaments and events
- 7075 aerospace-grade aluminum, hard-anodized finish
- Straightness tolerance +/-.005 in, weight tolerance +/-2.5%
- Factory assembled with UNI bushing, nock, point and vanes; made in the USA
What the research says: Easton's tuning guide says it recommends straightness within 0.004 in for best grouping, so a +/-.005 in tolerance sits just outside that figure; fine for learning, worth knowing if you aim for tight groups later. The listing gives no spine or length, so ask the program or Easton which size fits your bow weight. We could not open NASP's own rules to confirm the approval wording.
- Strengths: Arrives fully assembled; Straightness and weight tolerances stated; Program approval wording in the listing
- Limitations: Listing gives no spine number or shaft length in its feature text; Aluminum bends if it hits something hard; check shafts for straightness; Only six arrows per pack
- Suits: School, club and youth-program archers whose coach names this arrow, and beginners who want a ready-assembled aluminum shaft.
- Look elsewhere if: Anyone who needs a stated spine and length before ordering, or compound shooters with a fast, heavy bow.
2. SHARROW 30 in aluminum, spine 500 (12 pack): aluminum with a stated spine and glue-free nocks
One of the few aluminum listings that states a spine number, length and both diameters together, so you can compare it with a chart. Twelve in a pack leaves spares for a club or a family.
What the Amazon listing says
- Listing title: 30 inch aluminum arrows, spine 500, 12 pcs, blue shaft
- Material aluminum; spine 500; length 30 inches; OD 7.6 mm; ID 6.5 mm
- Screwed-on tips, replaceable
- Nock inserted, not fixed by glue, orientation adjustable
- Described for youth and adults; pack may include a quiver
What the research says: A chart cell gives a spine for a bow weight and an arrow length together, so a 500 at 30 inches only fits the bow weights where Easton's chart (or another maker's) lands on that number. The listing states no draw weight, so check a chart before you buy. Note that other makers' spine numbers are not always comparable with Easton's aluminum size codes.
- Strengths: Spine, length and diameters all stated; Nocks can be turned to fit the bow; Twelve-arrow pack
- Limitations: The listing does not state a draw weight range; Fixed 30 inch length may be too long for small archers; Straightness tolerance not stated
- Suits: Archers who know their chart spine is near 500 and who draw close to 28 inches or more.
- Look elsewhere if: Young or small archers, and anyone whose chart gives a different spine.
3. GPP 30 in fiberglass target arrows (12 pack): fiberglass for light recurve bows and teen beginners
The listing says it suits bows that do not weigh over 40 lb and youth over 12, with a stated shaft diameter and weight. Fiberglass is the material listings describe as hard to break.
What the Amazon listing says
- Listing title: GPP 30 inch fiberglass archery target arrows, 12 pack, blue
- Described as best for novice or occasional archers and as nearly indestructible
- Compatible with most bows as long as the bow does not weigh over 40 lb; suitable for youth over 12
- 30 inch fiberglass shaft, 6 mm OD, weight 28.5 g
- 2.5 inch shield vanes
What the research says: Fiberglass spine charts are not in the Easton material we opened, so use the maker's draw weight limit as your rule. Easton's chart also treats a wood or glass beginner limb as lowering effective bow weight by 5 lb, a reminder that a light training bow is a different case from a carbon-limbed bow.
- Strengths: Draw weight ceiling is stated; Described as very tough; Twelve-arrow pack
- Limitations: Only for light bows; the listing sets a 40 lb ceiling; 30 inches is long for smaller archers; No spine number stated
- Suits: Teens and adults on light recurve or traditional bows learning on a target.
- Look elsewhere if: Anyone shooting a heavier bow, or a compound; and children who draw well under 30 inches.
4. Bear Archery Youth fiberglass, 24 in (3 pack): youth fiberglass in a small card pack
A small, assembled youth arrow. It is the pick when you want to try a size on a child without buying a dozen.
What the Amazon listing says
- Listing title: Bear Archery youth fiberglass arrows, 24 inch, 3 pack
- Describes them as strong, durable and safe, with high-flexing qualities and no splintering
- Arrive with nock and points installed and pre-fletched with vanes
- Three arrows per card; four sizes available
What the research says: Easton's tuning guide notes that beginner recurve archers may want to add 1/2 to 1 inch to their arrow length so the arrow is not too short as they grow stronger. That is a small allowance, not permission to buy a much longer arrow; measure the child's draw and ask the coach.
- Strengths: Pre-fletched and ready to shoot; Short length for young archers; Small pack to try a size
- Limitations: Draw weight range and spine not stated; Three arrows is a small supply; Listing text is largely marketing wording
- Suits: Parents of young beginners who need a short arrow and want to confirm the size first.
- Look elsewhere if: Older archers or anyone who needs a spare set of dozens.
5. Hunter Ian pure carbon, spine 600 (6 pack): carbon with a stated light draw weight range
Many carbon listings claim a very wide bow-weight range. This one names a narrow, light range, 30 to 35 lb, and gives the straightness and weight per inch, so a light-bow archer can compare it with a chart.
What the Amazon listing says
- Listing title: Hunter Ian pure carbon arrows, 600 spine, 30 inch, turkey feather, pack of 6
- Shaft length 30 inch, whole length 31.5 inch, spine 600
- ID 6.2 mm, OD 7.1 mm, 5.54 grains per inch, straightness +/-0.006 in
- 100 grain screw-on field points with aluminum insert; 4 inch turkey feather
- For recurve, longbow and traditional bows, 30 to 35 lb
What the research says: A higher spine number means a weaker (more flexible) shaft, which is why a light bow can use a 600. Easton's tuning guide says tuning verifies a chart choice, so use this as a starting point and check how it flies. The straightness tolerance is looser than the 0.004 in Easton recommends for best grouping.
- Strengths: Narrow stated draw weight range; Straightness and grains per inch stated; Turkey feather fletching
- Limitations: Straightness +/-0.006 in is looser than other carbon listings here; Six arrows per pack; 30 inch shaft may be too long for small archers
- Suits: Recurve or longbow archers shooting a light bow in the stated range.
- Look elsewhere if: Heavier bows, and anyone who wants the tightest stated straightness.
6. Pinals carbon, spine 400, 12 pack with spare inserts: carbon with extra inserts for cutting to length
The listing includes twelve spare inserts and says the arrows can be cut shorter, which matters because the right length comes from your own draw. The stated draw range is wide, so check it against a chart.
What the Amazon listing says
- Listing title: Pinals archery hunting carbon arrows, spine 400, 30 or 32 inch shafts, feather arrow, 12 pack
- Pure carbon, ID 0.244 in (6.2 mm), 4 inch turkey feather, spine 400, for 25 to 70 lb bows
- Shaft weight, straightness and spine machine sorted (per the listing)
- Removable 100 grain points; 12 extra aluminum inserts for shafts cut shorter
What the research says: Easton's tuning guide says carbon shafts must be cut carefully (no rotary tube cutters or hacksaws) with a dust mask and safety glasses, so have a shop cut them. One spine cannot be right for both 25 lb and 70 lb in a chart, so treat the listing's range as the widest the arrow is described for, not a recommendation.
- Strengths: Spare inserts for shortening the shaft; Removable points; nock without glue; Twelve completed arrows
- Limitations: Draw weight range of 25 to 70 lb is very broad for one spine; Straightness tolerance number not given for this listing; Shaft length options not spelled out in the feature text
- Suits: Archers who need to trim arrows to their own length and want spares.
- Look elsewhere if: Anyone who needs a confirmed straightness number, or who wants a short ready arrow.
7. Linkboy pure carbon, many spine choices (12 pack): carbon with a wide spine range to choose from
The listing offers many spine numbers and states a +/-.003 in straightness, the tightest figure among the carbon listings here, which fits an archer who has already found their chart number.
What the Amazon listing says
- Listing title: Linkboy Archery pure carbon arrows, spine 300 to 1000, 12 pcs
- Straightness +/-.003 in, ID 6.2 mm, pure carbon shaft
- Stainless steel arrow tips included, removable
- Described as suiting compound, recurve, longbow and traditional bows
- Described for youth and adults, targeting and hunting
What the research says: A +/-.003 in tolerance is inside the 0.004 in Easton recommends for best grouping. Because the page lists nine spines, the choice rests on the chart: Easton says to find your bow weight in the chart, then read across to your arrow length.
- Strengths: Tight straightness stated; Many spine options; Removable stainless steel tips
- Limitations: Length and draw weight not stated in the feature text; Many options mean you must pick the spine yourself; Listing wording about competition is general
- Suits: Archers who already know their chart spine and want a number that matches.
- Look elsewhere if: First-time buyers who have not measured draw length or bow weight yet.
Accessories (separate from the main picks)
- Finger tab or glove: Protects fingers when drawing a recurve or traditional bow. Check size with your coach.
- Arm guard: Keeps the string off your forearm. Fit depends on arm length and sleeve.
- Quiver: Holds arrows safely on the range. Choose one that fits your arrow length and diameter.
- Arrow puller: Helps remove arrows from the target without bending or snapping shafts.
The three numbers: length, spine and material
Every arrow choice comes down to three things, and they depend on each other.
- Length is how long the finished arrow is. It follows how far you draw the string.
- Spine is how much the shaft bends when it is loaded. By the usual convention a lower number means a stiffer shaft and a higher number a more flexible one; the Easton pages we read do not spell this out, but the listings here follow it: the 600 spine listing is for a light 30 to 35 lb bow, while the 300 and 400 spine listings state heavier bows.
- Material is what the shaft is made of: aluminum, carbon or fiberglass in this guide.
Easton’s tuning guide says successful tuning needs a properly spined shaft, and it recommends starting from one of its selection charts, then confirming the choice by tuning. So the sequence is: measure your length, find your bow’s draw weight, read the chart, pick a material, then check how the arrows fly.
A shaft that is too stiff or too weak for the bow will not fly straight, however good it looks. That is why this guide spends more time on how to choose than on any single product.
How to measure the right arrow length
Easton’s tuning guide defines correct arrow length as the distance from the bottom of the nock groove to the end of the shaft. The point is not included. That is the length used for shaft selection.
The guide’s method is simple. Draw an extra-long arrow to full draw and have someone mark it. For target arrows it recommends marking about 1 inch in front of the point where the arrow touches the most forward part of the arrow rest. Other setups, such as hunting arrows with broadheads, use different clearances, so a coach or shop should do the measuring.
Two practical notes from the same guide:
- Beginners with recurve bows may want to add 1/2 to 1 inch so the arrow is not too short as technique and strength improve. That is a small allowance, not a reason to buy a very long arrow.
- Shaft cut length is slightly shorter than correct arrow length, because the nock base adds a little length.
Do not guess from height or age. Several listings here are a fixed 30 inches, and the youth listings run from 24 to 28 inches. Ask a trained coach to check your draw before you cut or buy.
How to read a spine chart
Easton’s target arrow size selection chart is one page. Here is how it works, in plain steps from the chart itself.
- Find the column for your arrow cut length, from 21 inches to 32 inches. If your length is fractional, round to the closest column: 28.25 inches goes to 28, and 28.5 goes to 29.
- Find the row for your actual bow weight. The rows run in bands, from under 20 lb up to 68 to 73 lb.
- Read the cell: it names the shaft size or spine range that fits.
The chart assumes a certain setup: a compound bow speed rating of 301 to 320 feet per second, glue-in 100 grain points and a mechanical release. If your setup differs, it tells you to add or subtract from your actual bow weight before reading it. A finger release adds 5 lb. Points lighter than 100 grain subtract 3 lb for every 25 grain. Heavier points add 3 lb for every 25 grain. For recurve bows, a carbon competition limb needs no adjustment, and a wood or glass beginner limb subtracts 5 lb.
For recurve bows the chart advises choosing the weaker side of the recommended spine range when several sizes fit. We could not read each individual cell reliably from the file, so use the original chart for your final number. Other makers publish their own charts and their numbers may not match.
Aluminum, carbon or fiberglass: how they differ
This section sticks to what the listings and Easton’s guide actually say.
Aluminum
Aluminum shafts are tubes. The Easton and SHARROW listings describe aluminum builds with stated tolerances or diameters. Easton’s guide describes deburring the inside of an aluminum tube after cutting, a job for a shop. Aluminum can bend, so check straightness.
Carbon
The carbon listings here (Hunter Ian, Pinals, Linkboy) give spine numbers and, for two of them, straightness figures. Easton’s guide warns that carbon is more susceptible to cracking when hit by a hard object or another arrow, and gives a check for cracks (see the care section). Carbon dust is a cutting hazard, so a mask and glasses are advised.
Fiberglass
The GPP and Bear listings describe fiberglass as tough, with stated weight limits for the bow. The GPP listing sets a 40 lb ceiling. These suit light bows and learning.
No single material is best for everyone. Pick by bow weight, who is shooting and what program rules require. A material that the listing describes as durable is not a safety guarantee; inspect any arrow before you shoot it.
By age and level, without the price tag
Think in three steps rather than one big decision.
Children and first-time beginners
A short, assembled fiberglass or aluminum arrow in a small pack is a sensible start, such as the Bear Archery 24 inch card or a school-program aluminum arrow. Buy the length measured for the child’s draw. Do not buy long shafts to grow into: a shaft that is too long is both less safe and harder to control. Easton’s small allowance of 1/2 to 1 inch for recurve beginners is the most the guide mentions.
Teens and adults on light recurve or traditional bows
Fiberglass with a stated bow limit (GPP), or a light-spine carbon listing with a narrow range (Hunter Ian 600), fit this group. Check the draw weight at your draw length, not just the number on the limb.
Returning and club archers
If you know your chart spine, a carbon listing with a stated straightness (Linkboy) or an aluminum arrow with a stated spine (SHARROW) lets you match it. Skill level matters less than bow weight for the spine, but it matters for how fussy you need to be about tolerances.
Compound bows are fast and heavy, which is why Easton’s chart adds weight for faster bows. If you shoot a compound, use the compound rows and ask a shop to measure.
Draw weight and the wide ranges on listings
Several carbon listings state very wide draw weight ranges: Pinals says 25 to 70 lb for its spine 400, and others claim similar spreads. A chart works differently. At a given arrow length, each bow-weight band points to a spine range. One spine cannot fit both ends of a 25 to 70 lb spread, so treat the listing’s range as the outer limit the maker describes, not as proof that the arrow is right for your bow.
The more specific the listing, the easier it is to check. The Hunter Ian listing says 30 to 35 lb for spine 600, and the GPP listing says up to 40 lb for fiberglass. Those narrow ranges are easier to match to a chart than a 25 to 70 lb claim.
Draw weight itself must be your actual weight at your draw length. Easton’s chart says to use actual bow weight. If you are not sure, a bow shop can measure it with a scale. We did not open a source for how limb ratings convert to your own draw length, so ask the bow maker or shop.
Points, fletching and nocks
The shaft is only part of the arrow. Easton’s chart assumes 100 grain points, so a heavier or lighter point changes the result, as the adjustments above show. The carbon listings here ship with 100 grain field points that screw in, which is the weight the chart treats as no adjustment.
Fletching steers the arrow. The listings use turkey feathers (Hunter Ian, Pinals) or plastic vanes (Genesis, GPP, SHARROW). Easton’s tuning guide says that if fletching is even slightly detached the arrow may not group, and that a bent rear on a hard vane can cause large deviation in where it lands.
Nocks hold the string. Several listings describe nocks that are not glued and can be turned. The guide says a nock turned differently from the rest can cause a clearance problem. Check them all the same way.
Points can loosen on impact. The guide says to grip the point with pliers and the shaft with a rubber gripper to tighten it. The Pinals listing mentions a rubber ring meant to reduce loosening, per the listing.
Essential and optional features
- Essential: the right length for your draw; a spine that matches your bow weight and length on a chart; straight shafts; securely fixed nocks and points; undamaged fletching.
- Useful: a stated straightness tolerance (the Linkboy listing states +/-.003 in), a stated draw weight range, replaceable nocks and removable points so worn parts can be swapped.
- Optional: bright colors, feather versus vane, matched sets with spares, camouflage patterns.
Easton recommends straightness within 0.004 in for best grouping. That is a figure from the maker, and it matters more as you improve. A beginner learning form may not notice a difference, but it helps to know which listings state a number.
Care, inspection and when to replace
Easton’s tuning guide says to inspect arrows before shooting. Its advice, in plain words:
- Carbon: check every carbon shaft for cracks or damage. Hold the shaft near the point and near the fletching, then rotate it while bending it gently. If it feels rubbery, creaks or rotates strangely, do not shoot it again. A cracked carbon arrow can break when released and injure the shooter.
- Dented or cracked shafts: discard them.
- Straightness: Easton says arrows must be straight for tight grouping; a shop can check yours.
- Fletching and nocks: replace loose or damaged fletching, and check that nocks are straight and turned the same way.
- Points: tighten loose points.
Store arrows so they cannot bend or be stepped on. Pull them from the target straight, with an arrow puller if you have one. There is no set lifespan in the sources we opened; replace an arrow when it is damaged, bent or unreliable. If you hit another arrow or a hard object, inspect the shaft before shooting again.
Common mistakes when buying arrows
- Guessing length. Measure draw length with a coach. Length affects both fit and spine.
- Buying by the box range. “Fits most bows” is not a spine choice. A chart looks at your actual bow weight and length.
- Buying long to grow into. Easton allows 1/2 to 1 inch for recurve beginners. Beyond that, an oversize arrow is a safety risk, especially for children.
- Ignoring the weak or stiff side. For recurve, Easton’s chart says to lean toward the weaker side when several sizes fit.
- Cutting carbon with a hacksaw or tube cutter. Easton’s guide says never to use these, and to wear a mask and glasses. Have a shop cut it.
- Skipping the crack check. Carbon can crack without looking broken.
- Changing several things at once. Easton’s tuning guide says to change one variable at a time.
Myths and facts
- Myth: a higher spine number means a stiffer arrow. Fact: the usual convention, which the listings here follow, is the other way (not stated in the Easton pages we read). The 600 spine listing is for a 30 to 35 lb bow, while the 300 and 400 spine listings state heavier bows. A lower number is stiffer.
- Myth: one arrow fits any bow. Fact: charts use bow weight and length together. Listings with 25 to 70 lb ranges describe the widest case, not your bow.
- Myth: expensive arrows are always necessary. Fact: the sources we opened say nothing about cost. For learning, correct size matters more than premium tolerances.
- Myth: carbon never breaks. Fact: Easton’s guide says any carbon shaft is more susceptible to cracking if it hits a hard object or another arrow.
- Myth: any arrow can go into any program. Fact: some programs name an approved arrow, as the Genesis listing states for NASP. Ask yours.
What to buy first and what can wait
- Get your draw length and bow weight checked. Ask a club or bow shop to do it.
- A small set of arrows in the right length and spine. Six to twelve is enough to start. A small card, like the Bear Archery listing, lets you confirm a size.
- A finger tab or glove and an arm guard for recurve and traditional shooting.
- A quiver and an arrow puller.
- Spare nocks and points. Several listings include extras.
- Higher-tolerance carbon arrows later, once your form is consistent and you know your tuned spine.
Do not spend on matched, high-tolerance sets until your length and spine are settled. You can learn with a plain, correctly sized arrow.
One-minute checklist
- Is my draw length measured by a coach?
- What is my bow’s actual weight at that draw length?
- Does the chart for my bow type give a spine for that length and weight?
- Does the listing state that spine, length and draw weight, or only a wide range?
- Is this material right for the bow: fiberglass for light bows, aluminum or carbon for the rest, per the listing limits?
- Does my program require a specific arrow?
- Have I got a way to check carbon arrows for cracks?
If you can answer all seven, the table above narrows to one or two listings.
Glossary of terms
- Spine. How much a shaft bends under load. By the usual convention, lower numbers are stiffer.
- Draw length. How far you pull the string to full draw.
- Draw weight. The force needed to hold the bow at your draw length.
- Correct arrow length. Per Easton, from the bottom of the nock groove to the end of the shaft; the point is not included.
- Shaft. The tube of the arrow, without nock, point or fletching.
- Nock. The notch that holds the string.
- Insert. A small part glued into the shaft front that the point screws into.
- Fletching. The feathers or plastic vanes that steer the arrow.
- Straightness. How closely the shaft runs straight, given as a tolerance in inches.
- GPI. Grains per inch, a weight measure used in some listings.
- Field point. A target point, as opposed to a broadhead for hunting.
Safety and where to shoot
Arrows are not toys. Whatever you buy, use it only on a range or with a proper target. One listing here adds a plain warning to shoot only at a target and never aim at people or animals. We could not open USA Archery or World Archery safety rules for this guide, so follow your range or club rules.
- Inspect arrows before every session.
- Do not shoot an arrow that is cracked, bent or has a loose point.
- Do not shoot an arrow whose point cannot clear the bow safely at full draw; a coach should confirm length.
- Keep children supervised and match equipment to their size.
Easton’s guide also warns that carbon shafts shatter into splinter-like fragments if broken; treat any broken shaft with care. None of this replaces instruction from a trained coach.
Related gear and what else archers need
Arrows are one part of the kit. See our archery targets guide for something safe to shoot into, and the archery gear page for the rest. After long sessions, shoulders and back can feel tight; our foam roller guide and recovery routine cover simple routines. Focus is a big part of archery, and our mental training tools guide may help. We did not review bows, sights or releases here; check the maker’s sizing for those.
How we chose these picks
This is a research-based comparison, not a hands-on test. Selection and fit rules come from two Easton documents opened on 2026-11-13: the Target Arrow Size Selection chart (PN 301055-A) and the Arrow Tuning and Maintenance Guide. Product facts come only from the Amazon listing text for each ASIN in our candidate file. We did not shoot, measure or test any arrow, and we do not use ratings, reviews or sales rankings. Picks span aluminum, carbon and fiberglass, light and heavier bows, and youth sizes, chosen for fit to a stated use rather than for commission. We could not open NASP, USA Archery or World Archery rule pages, so program approvals and governing-body rules are described only as the listings state them. No prices are quoted because they change.
Sources
- Easton Archery, Target Arrow Size Selection chart (PN 301055-A, adjustments and chart rules) (checked 2026-11-13)
- Easton Archery, Arrow Tuning and Maintenance Guide (arrow length, cutting, inspection) (checked 2026-11-13)
- Amazon product listing (ASIN B0C3S13DWG) (checked 2026-11-13)
- Amazon product listing (ASIN B07SR44PH7) (checked 2026-11-13)
- Amazon product listing (ASIN B01M16AUDH) (checked 2026-11-13)
- Amazon product listing (ASIN B0002F7MIQ) (checked 2026-11-13)
- Amazon product listing (ASIN B08H4X1D74) (checked 2026-11-13)
- Amazon product listing (ASIN B08MD6CG9J) (checked 2026-11-13)
- Amazon product listing (ASIN B0F3J8NTQK) (checked 2026-11-13)
Frequently asked questions
What spine arrow do I need?
It depends on your bow's actual weight at your draw length and on your arrow length. Easton's chart gives a spine range for each combination, so find your bow weight row and your length column. Ask a shop to check the result.
How long should my arrows be?
Easton's tuning guide measures correct arrow length from the bottom of the nock groove to the end of the shaft, found by marking an extra-long arrow at full draw. Beginners on recurve may add 1/2 to 1 inch. Have a coach check it.
What size arrow for a child?
Use the length measured from the child's own draw and ask the coach. Youth listings here run from 24 to 28 inches. Do not buy long arrows to grow into.
Is a higher spine number stiffer or weaker?
Weaker, by the usual convention (not spelled out in the Easton pages we read). The listings follow it: spine 600 for a 30 to 35 lb bow, while the 300 and 400 listings state heavier bows. Lower numbers are stiffer.
Are carbon arrows better than aluminum?
Neither is better for everyone. Carbon listings here state spine and straightness figures, while aluminum offers an assembled, program-approved option. Easton warns carbon can crack, so inspect it each time.
Can I cut my own carbon arrows?
Easton's guide says never to use rotary tube cutters or hacksaws on carbon, and to wear a dust mask and safety glasses. Most beginners are better off having a shop cut them.
Can fiberglass arrows be used with a compound bow?
The GPP listing says up to 40 lb and for recurve and traditional bows, and the Bear listing does not give a limit. Check each maker's limit and, for a compound, ask a shop.
How long do arrows last?
There is no fixed lifespan in the sources we opened. Replace an arrow when it is cracked, dented, bent, or will not group. Check carbon after each shot, as Easton advises.
What does arrow straightness mean?
It is how closely the shaft runs straight, given as a tolerance in inches. Easton recommends straightness within 0.004 in for best grouping. The listings here state +/-.003, +/-.005 or +/-.006 in.
Do I need a spine chart if the listing says it fits my bow?
Yes, check one. Listings often state broad ranges, such as 25 to 70 lb, which a chart would split into several spines. Your actual bow weight and length decide.
Do heavier points change the spine I need?
Yes. Easton's chart adds 3 lb to your bow weight for every 25 grain over 100, and subtracts 3 lb for every 25 grain under. The chart assumes 100 grain points.
What is a NASP arrow?
The Genesis listing says it is the official NASP approved arrow for NASP tournaments and events. We could not open NASP's pages, so ask your program what it requires.